Tag: Tubes

Tubelab Simple PP

by on Apr.28, 2010, under Electron Tube Audio

George from Tubelab was kind enough to send me his latest PCB and some iron for a test build. Easy build and the result was tossed into a disused lock box.

Angle shot of the chassis running JJ tubes


Leave a Comment : more...

Tubelab Simple SE Chassis Fitting

by on Apr.17, 2009, under Electron Tube Audio

All of the cutting and milling and drilling is finally done.

Chassis parts to be test fitted

Here are all the various bits and pieces, made mostly from scraps, all put together:

All components being test fitted to check for clearance issues

More about the build here. Next step is paint….

Leave a Comment : more...

Tubelab SE Breadboard with 300Bs

by on Apr.15, 2009, under Electron Tube Audio

With a custom power transformer from Edcor, I could finally try this amp with some borrowed 300Bs. This transformer’s primary is tapped so that it can be used with either 300Bs or 45s:

XPWR131 - 330-260-0-260-330 @ 175mA, 6.3 V CT @ 4A, 5V @ 3A

Tubelab SE - Testing Edcor 45

Voltages came in a bit high, even under load. The top row is the Tubelab SE in “45 mode”, with about 25mA per tube. Meters are reading: 660VAC winding, 520VAC winding, B+ at the filter cap. Bottom row is in “300B mode”, running Shuguang 300Bs (not mine) at about 28mA per tube. First two meters got swapped: 520VAC winding, 660VAC winding, B+.

Tubelab SE - Testing Edcor B+

With the 300Bs biased to 80mA, the 660VAC winding gets pulled down exactly to spec: 660VAC. B+ sags to around 370-375 VDC. Supposedly this is the ideal spot for the 300B. These tubes are Shuguang’s aptly-named “300BS”, which have mesh plates and globe-shaped glass. They have a weird blue glow on the glass, presumably from electrons flying through the gaps in the mesh.

Tubelab SE - Testing 300BS Dark

2 Comments : more...

Tubelab Simple SE Breadboard

by on Mar.22, 2009, under Electron Tube Audio

With the right iron, the Tubelab Simple SE comes to life. After a sanity-check with cheap Chinese tubes, here is the amp running with JJ 6L6GCs strapped as triodes. The amp sounds sweet with a bit more power than the Tubelab SE.

Tubelab Simple SE - Breadboard Testing

This coincides with the new speakers that I recently got off of Craigslist: a pair of Klipsch KLF-10s. The horns on these do cause ear fatigue on the Dynaco, but with this amp it is more subdued. I am hoping that the DHTs in the Tubelab SE will be even better.

Tubelab Simple SE - Breadboard Testing System

The basement in currently under construction, so the setup is a bit MacGyver.

2 Comments : more...

Tubelab SE Breadboard

by on Mar.16, 2009, under Electron Tube Audio

So I’ve finally built-up this Tubelab SE, a small, single-ended, 2 watt amp. It’s currently in breadboard form, but it sounds amazing. Awesome detail, impressive bass, and something warm about the sound.

Tubelab SE - Testing 45s

Leave a Comment : more...

Tube Fluorescence

by on Feb.03, 2009, under Electron Tube Audio

Night Shot - Amplifier
These are the output tubes on my Thomas amp. You can see the blue glow against the glass from stray electrons. This is very common with Sylvania tubes. Behind the blue glow, is the red glowing line from the electron beam hitting the plates (I can’t get the bias to go any lower with this amp). The two together look purple to the camera.

I have read contradictory discussions about blue glow against the glass envelope. Blue glow coming from inside or near the anode or other structures is normal, but some say that blue glow outside of that means a soft vacuum. Sylvania claims the opposite and that fluorescent glow inside the envelope is normal for some tubes. It results from stray electrons bombarding near the glass envelope and will change in brightness depending on the intensity of the signal passing through the tube. This is exactly what I see with these Philips JAN tubes, which are basically Sylvania. In fact when I push the amp really hard well into cut-off, the tubes will flash brightly signaling me to back-off

The “Winged-C” SED EL34s in the Dynakit seem to fluoresce at the screen behind the plate:

Dynakit VTA-70 - SED EL34 Fluorescence

2 Comments : more...

Made in Chian

by on Jan.29, 2009, under Electron Tube Audio

Made in Chian
All the best stuff comes from Chian.

2 Comments : more...

Why Tubes?

by on Feb.01, 2003, under Electron Tube Audio

Why thermionic electron emission devices (valves to our friends in the UK)?  Well, I grew up listening to my LPs, cassettes, and the radio through a 6V6GT push-pull instrument amplifier and eventually found that I really missed its sound.  I actually didn’t know what it was I didn’t like about my audio system until I fired up that old amp again.  The brash, gritty sound was gone.  See my Thomas 6V6GT PP amp for more about that.  I don’t consider myself to be an audiophile, however the difference to me is noticeable.  For an excellent article with a bit of empirical evidence, take a look at Tubes Vs. Transistors by Russell O. Hamm.

The other part of the answer to this question is that I enjoy the challenge as much as (if not more than) the results of my efforts.  In terms of components in the signal path, electron tube amplifiers are about as simple as it can get.  Perhaps some of the healthy fear involved in working with lethal voltages has something to do with it as well. 🙂  Finally, tubes are just damn cool.  They operate on such a macro scale that you can actually “see” the process take place inside them that is providing you with service that you took the time to design/modify.  They’re also pretty to look at….

Leave a Comment : more...


Use the form below to search the site:

Still not finding what you're looking for? Drop a comment on a post or contact me.

Sites that interest me

A few highly recommended friends...